FAQs
VelocityOne Flight - Re-Calibration Process
- Disconnect the VelocityOne Flight from the console/PC it is being used with.
- Hold the Menu and View buttons (highlighted in blue in the image below) down at the same time. ...
- Connect the VelocityOne Flight back to the console/PC.
Calibrating the Controls
- Push the yoke full forward, and turn it full right.
- While holding full right, pull the yoke full back.
- While holding full back, turn the yoke full left.
- While holding full left, push the yoke full forward.
- While holding full forward, turn the yoke full right.
- Repeat above steps (1x).*
Connect the VelocityOne Flight's included cables to the unit itself, and then to respective ports on the console/throttle quadrant. Please note that these cables and jacks are color coded and are not interchangeable. 6. Ensure that the Xbox Mode is selected on the Velocity Flight menu.
How do you fix an unresponsive Turtle Beach headset? ›
Open the Turtle Beach Audio Hub (for Windows or MacOS). Connect the USB Charge Cable to the Headset's USB Charge/Update port. (With the Headset powered OFF) Hold down the Superhuman Hearing™ button while connecting the USB Cable into your computer. The Audio Hub will prompt you to update the headset.
How do you reset turtle position? ›
Checking and Resetting Turtle Position
We've already seen that you can reset a turtle position with the forward command. In addition, you can check a turtle position with the properties xcor and ycor, and use setx, sety, and setxy to reset these positions.
What does factory resetting a headset do? ›
If you run into problems with your headset or want to clear all of your data off of the headset, you can perform a factory reset. This erases everything off your headset and returns it to the software state that it was in when you first took it out of the box.
How to do a hard reset on wireless headphones? ›
With the product turned on and not connected with a Bluetooth device, press and hold (about 6 seconds) the power supply/control button and volume buttons (+/-) at the same time. After the indicator lamp lights in red, the product will restart, and the reset will be complete.
How do I soft reset my headset? ›
To soft reset your headset:
- Make sure your headset is currently unplugged.
- Make sure your headset is powered off.
- Hold the Mute button on the headset down for about 15 seconds.
- Hold down the power button until the headset turns on.
- Test your headset and see if the issue is resolved.
In velocity calibration, the gauge measures the speed of sound in a reference sample of the test material and then stores that value for use in calculating thickness from measured time intervals.
What does calibrating a controller do? ›
By calibrating your gaming controller, you can fine-tune its sensitivity and responsiveness, resulting in better accuracy while gaming. You can calibrate your controller from the same menu where you initially tested it. Here are the steps you can follow. Open game controller settings on Windows.
Recommended Tuning Steps
- setting the reference value of velocity to 50% of its rated value. Increase kP until the measured speed is around 70% of the reference speed. ...
- increasing kP to increase the actual speed. ...
- Increasing kI until a proper step response is generated by the velocity controller.
The Turtle Beach® VelocityOne™ Flightstick for Xbox Series X|S, Xbox One & Windows PCs equips you with immersive, accurate controls for air and space flight simulation & combat games on Xbox and PC.
How to update Velocity One on Xbox? ›
VelocityOne Flightstick - Firmware Update – v. 1.1. 6, Released 1/18/2023
- Download the VelocityOne Flightstick Companion App on your Xbox or Windows PC.
- Plug the Flightstick in to the Xbox/PC. ...
- Launch the app, and follow the on-screen instructions to perform that firmware update.
Press the Pairing Button on the Xbox One Console. The LED on the Console itself should start blinking, indicating that the Console is in Pairing Mode. Press and Hold the Connect Button on the Headset until the Headset's Power LED flashes rapidly, indicating that the headset is in Pairing Mode.
How do I reset my Turtle Beach Xbox controller? ›
To reset the controller to factory default, please do the following:
- Connect the Type-C cable to the controller. ...
- Press and hold down all ABXY face buttons; at the same time, connect the Type-A end to the PC or Xbox. ...
- Do not release the buttons until all of the LEDs on the controller illuminate.
To do this:
- 1) Power the headset off by holding the power button on the headset for 3 seconds. ...
- 2) Disconnect the USB transmitter cable from the USB port on your Xbox One.
- 3) Power off the Xbox One. ...
- 4) Power the Xbox One back on. ...
- 5) Plug the USB transmitter cable back into a USB port on your Xbox One.
Press the controller's Input Focus Button (“+”), then press Y to open the Main Menu. Press right on the D-Pad to go to SYSTEM and press A. Next, press right on the D-Pad until you get to CALIBRATION, and press A. Here, you will have options to calibrate the STICKS and the TRIGGERS.
